The following is the correct way to use Shortwave Infrared Heating Elements: I. Before installationCheck the productBefore installing the electric infrared heat lamp, carefully check the appearance of the quartz heating tube for damage, cracks and other defects. If there is obvious damage, contact the supplier immediately for replacement to avoid safety problems during use.Confirm whether the power, voltage and other parameters of the Halogen Quartz IR Heat Lamps are compatible with the use environment. For example, make sure that the voltage of the power supply is stable and meets the rated voltage requirements of the heater, generally 2500W and 3000W infrared heater usually requires higher voltage support, check whether the wiring can withstand the corresponding load.Choose the right installation locationAccording to the actual use requirements, choose the appropriate installation location. Consider factors such as the location and shape of the heating object and the uniformity of the heating. For example, in industrial drying equipment, to ensure that the Infrared Heat Lamp Replacement can evenly irradiate the surface of the material to be dried, a combination of multiple Industrial Infrared Heat Lamps can be installed to improve the heating effect.The installation location should be far away from flammable and explosive substances and water sources that may cause damage to the heating pipe or cause safety accidents. At the same time, to ensure that the installation location has enough space for heat dissipation, to avoid damage to the heating pipe or the surrounding equipment due to heat accumulation. Second, when installingCorrect fixingUse a suitable mounting bracket or fixing device to firmly fix the infrared heating tube in the selected position. Ensure that the heating tube in the working process will not shake or shift, so as not to affect the heating effect or cause potential safety hazards.When fixing, be careful to avoid exerting excessive pressure on the heating tube, so as not to damage the internal structure of the heating tube. You can use spring clamps, screws and other fixed parts to ensure that the fixed firmly and will not cause damage to the heating tube.Connecting linesConnect the wiring in strict accordance with the electrical connection requirements of the heater. Generally speaking, the power of the infrared heat emitter should be used to match the power of the wire, and ensure that the connection is firm and good contact.For the connection of multiple heating tubes, pay attention to the use of the correct parallel or series connection to ensure that the operating voltage and power of each heating tube meets the requirements. At the same time, we should do a good job of insulation and protective measures of the line to avoid leakage or short circuit and other accidents. Third, in usePreheating and warmingWhen restarting the infrared heater after the first use or a long period of non-use, it should be preheated first. Slowly increase the power of the heating tube, let it gradually warm up to the working temperature, to avoid damage to the heating tube and heated objects due to instantaneous high temperature.Preheating time can be based on the power of the heating tube and the use of the environment, generally ranging from a few minutes to ten minutes. In the preheating process, we should closely observe the working status of the heating tube, if there are any abnormalities, we should immediately stop heating and check.Temperature controlAccording to different heating requirements, set the appropriate temperature control parameters. Temperature controllers, thermocouples and other equipment can be used to monitor and control the temperature of the heating tube to ensure that the heating temperature is within the safe range and meet the process requirements.In the temperature adjustment process, the heating power should be gradually adjusted to avoid excessive temperature fluctuations on the heated object causing adverse effects. At the same time, the accuracy and reliability of the temperature control equipment should be checked regularly to ensure its normal operation.Safety ProtectionWhen using infrared heating tubes, safety protection measures should be done. For example, set up guardrails or warning signs around the heating area to prevent personnel from accidentally touching the heating tube and causing burns.For the operation of high temperature environment, the operator should wear appropriate protective equipment, such as high temperature gloves, goggles and so on. At the same time, it is necessary to ensure that the workplace is well ventilated to avoid hazards to personnel due to heat accumulation and harmful gas emissions. Regular Inspection and MaintenanceRegularly check the working condition of the tungsten halogen lamp, including whether there is any damage to the appearance, whether the connecting lines are loose, and whether the temperature control is accurate. If any problem is found, it should be repaired or replaced in time.Regularly clean the dust and dirt on the surface of the Infrared Heat Lamp for PET Blowing Machines to maintain its good heat dissipation performance and heating efficiency. You can use compressed air or a soft cloth for cleaning, but be careful to avoid using sharp objects to scrape the surface of the Infrared Lamp for Injection Machines so as not to damage its coating. For heating tubes that have been used continuously for a long time, regular maintenance should be carried out according to their usage and manufacturer’s recommendations, such as replacing aging parts, checking insulation performance, etc., to ensure their safe and reliable operation.

Similar Posts